收藏本站
Micrel, Inc.
MIC3291
Shutdown
Whenever a logic level LOW is applied to the DC input
pin for a period greater than or equal to
t SHUTDOWN (1260μs), the MIC3291 will be in power saving
shutdown mode.
Figure 5. Mode Change to Count Down
Programming the Brightness Level
MIC3291 is designed to start driving the output LEDs
(t START_UP ) in 140μs at the maximum brightness level of
15. After startup, the internal control logic is ready to
decrease the LED brightness upon receiving
programming pulses (negative edges applied to DC pin).
Since MIC3291 starts in count down mode, the
brightness level is decreased one level by applying two
Figure 3. Shutdown Timing
Once the device is shutdown, the boost supply is
disabled and the LEDs are turned off. Brightness level
information stored in the MIC3291 prior to shutdown will
be lost.
Programming Pulse Counter Modes
At power up the MIC3291 defaults to count down mode.
In count down mode, the brightness level is decreased
one level by applying two programming pulses, as
shown in Figure 6. The counting mode can be changed
to count up mode by pulling the DC pin LOW for a period
equal to t MODE_UP (100μs to 160μs). The device will
remain in count up mode until its state is changed to
count down mode or by disabling the MIC3291.
Figure 4. Mode Change to Count up
To change the state back to count down mode, pull the
DC pin LOW for a period equal to t MODE_DOWN (420μs to
500μs). Now the internal circuitry will remain in count
down mode until changed to count up mode as
described previously.
programming pulses, as shown in Figure 6. Each
programming pulse has a high (t PROG_HIGH ) and a low
(t PROG_LOW ) pulse width that must be between 1μs to
32μs. Note that n+1 number of pulses are needed to
decrease brightness by n level(s) since the first clock
pulse is ignored. Ignoring the first clock pulse is
necessary so mode change (t MODE_UP , t MODE_DOWN ) pulses
do not result in adjustments to the brightness level. The
MIC3291 internal circuit can be changed from count
down mode to count up mode and vice versa. The user
may elect to send a mode change as shown in Figure 4
to set the MIC3291 to step up the brightness level with
subsequent programming pulses. For proper operation,
ensure the DC pin has remained HIGH for at least
t DELAY (140μs) before issuing a mode change command.
Figure 6. Brightness Programming Pulses
Multiple brightness levels can be changed together with
multiple programming pulses, as shown in Figure 7.
When issuing multiple brightness level adjustment
commands to the DC pin, ensure both t PROG_LOW and
t PROG_HIGH are within 1μs and 32μs.
September 2010
10
M9999-092810
(408) 944-0800
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
MIC4100YM IC DRIVER MOSFET 100V CMOS 8SOIC
MIC4102YM IC DRIVER MOSFET 100V TTL 8SOIC
MIC4103YM IC MOSFET DRIVER 100V CMOS 8SOIC
MIC4124YME IC MOSFET DRVR DUAL NONINV 8SOIC
MIC4128YMME IC DRIVER MOSFET 1.5A DUAL 8MSOP
MIC4129YME IC MOSFET DRIVER 6A INVERT 8SOIC
MIC4223YM IC MOSFET DVR DUAL-INV 4A 8-SOIC
MIC4417YM4 TR IC DRIVER MOSF LOW SIDE SOT143-4
相关代理商/技术参数
MIC3291-18YML-TR 功能描述:LED 驱动器 IC 1 输出 DC DC 稳压器 升压（升压） 1.2A（开关） 8-MLF?（2x2） 制造商:microchip technology 系列:- 包装:剪切带（CT） 零件状态:过期 类型:DC DC 稳压器 拓扑:升压（升压） 内部开关:是 输出数:1 电压 - 供电（最低）:2.5V 电压 -?供电（最高）:6.5V 电压 - 输出:- 电流 - 输出/通道:1.2A（开关） 频率:1.2MHz 调光:- 应用:背光 工作温度:-40°C ~ 125°C （TJ） 安装类型:表面贴装 封装/外壳:8-VFDFN 裸露焊盘，8-MLF? 供应商器件封装:8-MLF?（2x2） 标准包装:1
MIC3291-25YD6 制造商:MICREL 制造商全称:Micrel Semiconductor 功能描述:1.2MHz PWM White LED Driver with Internal Schottky Diode and Single-Wire Linear Brightness Control
MIC3291-25YD6 TR 功能描述:LED照明驱动器 1.2MHz PWM WLED Driver w/Internal Schottky Diode & Single-Wire Linear Brightness Control (Lead Free) RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N
MIC3291-25YM6 制造商:MICREL 制造商全称:Micrel Semiconductor 功能描述:1.2MHz PWM White LED Driver with Internal Schottky Diode and Single-Wire Linear Brightness Control
MIC3291-25YML TR 功能描述:LED照明驱动器 1.2MHz PWM WLED Driver w/Internal Schottky Diode & Single-Wire Linear Brightness Control (Lead Free) RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N
MIC3291-25YML-TR 功能描述:LED 驱动器 IC 1 输出 DC DC 稳压器 升压（升压） 1.2A（开关） 8-MLF?（2x2） 制造商:microchip technology 系列:- 包装:剪切带（CT） 零件状态:过期 类型:DC DC 稳压器 拓扑:升压（升压） 内部开关:是 输出数:1 电压 - 供电（最低）:2.5V 电压 -?供电（最高）:6.5V 电压 - 输出:- 电流 - 输出/通道:1.2A（开关） 频率:1.2MHz 调光:- 应用:背光 工作温度:-40°C ~ 125°C （TJ） 安装类型:表面贴装 封装/外壳:8-VFDFN 裸露焊盘，8-MLF? 供应商器件封装:8-MLF?（2x2） 标准包装:1
MIC3300AFLMGNHWS 制造商:Vishay Dale 功能描述:THIN FILM RESISTOR,330 OHM,1%,200PPM - Trays
MIC33030 制造商:MICREL 制造商全称:Micrel Semiconductor 功能描述:8MHz 400mA Internal Inductor Buck Regulator with HyperLight Load